This is an old revision of the document!
Welcome to RepRap DIY, outlet of Markus “Traumflug” Hitter, developer of RepRap's Generation 7 Electronics.
Generation 7 Electronics
Generation 7 Electronics is a RepRap controller designed to be do-it-yourselfable and replicable. Replication is what makes RepRap unique.
The circuitry design is very similar to other single/stacked board solutions, like RAMPS or Sanguinololu. Generation 7 Electronics can drive the same hardware, can run the same firmwares. Additionally, it comes with a number of detail improvements to make it more flexible, as well as more reliable.
For details, see Generation 7 Electronics in the RepRap Wiki. The PCBs are manufactured on a RepRap machine and the kit's contents match the tables on the Wiki page, including connectors and solder/crimp pins. The ATmega is equipped with a bootloader already, so there's no need for a programmer.
Orderable Items
Name | Price with VAT | Price without VAT |
Gen7 v1.5 PCB, including developer donation | EUR 16.50 | EUR 13.90 |
Gen7 v1.5 Components Kit (with ATmega1284P and bootloader) | EUR 25.50 | EUR 21.40 |
Gen7 v1.5 Connectors Kit | EUR 13.50 | EUR 11.30 |
Gen7 Opto Endstop PCB (one piece) | EUR 2.- | EUR 1.70 |
Gen7 Opto Endstop Parts Kit (for one endstop) | EUR 2.- | EUR 1.70 |
ATmega1284P alone, with bootloader | EUR 8.- | EUR 6.70 |
Shipping International | EUR 5.- | EUR 5.- |
Shipping International PCB only | EUR 2.50 | EUR 2.50 |
Prices including VAT apply to citizens of the European Union. Customers outside the European Community qualify for the VAT-free, lower prices.
To make use of the sets, you likely also need the following parts:
- 4 “Pololus” or “StepSticks”. These are the same as on other RepRap controllers, so whatever works on a RAMPS, works on a Gen7, too.
- A power supply, capable of delivering 5 Volts and 12 Volts, prefered a PC power supply > 200 Watts (without heated bed) or > 450W (with heated bed).
An often requested combination includes the following:
- 1x Gen7 v1.5 PCB
- 1x Gen7 v1.5 Components Kit
- 1x Gen7 v1.5 Connectors Kit
- 3x Gen7 Endstop PCB
- 3x Gen7 Endstop Parts
- Shipping
SevenSwitch
The SevenSwitch is a general purpose DC switch, useful for operating heated beds, heaters, fans and similar devices by 5 V operated electronics, like Generation 6 Electronics, RAMPS, Sanguinololu, Generation 7 Electronics and similars. The only input needed is a 5 V signal. It's fast enough to run at 80 kHz PWM, strong enough to switch up to 15 Ampéres and allows voltages of up to 30 V, including 12 and 24 Volts.
For details, see SevenSwitch in the RepRap Wiki. The PCBs are manufactured on a RepRap machine. The Parts Kit matches the table on the Wiki page, including alternative parts for all configurations, pluggable connectors as well as screw terminals, 12 V and 24 V variants.
Orderable Items
Name | Price with VAT | Price without VAT |
SevenSwitch 1.2 PCB, including developer donation | EUR 3.- | EUR 2.50 |
SevenSwitch 1.2 Parts Kit (Components & Connectors) | EUR 5.40 | EUR 4.50 |
SevenSwitch 1.2 readily soldered | EUR 13.30 | EUR 11.20 |
Shipping International | EUR 5.- | EUR 5.- |
Shipping International PCB only | EUR 2.50 | EUR 2.50 |
Prices including VAT apply to citizens of the European Union. Customers outside the European Community qualify for the VAT-free, lower prices.
Ordering
For now, please order by emailing to Traumflug (mah@jump-ing.de).
For European Citizens, payment via (SEPA) bank transfer is somewhat preferred (no fees here)
Account no.: 7334010 Account holder: Markus Hitter IBAN: DE38 2009 0500 0007 3340 10 BIC/SWIFT-Code: GENODEF1S15 (Netbank AG, Germany)
alternatively, PayPal is also fine (fees about EUR 1.50 here)
Account mah@jump-ing.de
Addresses, legal stuff
RepRap DIY is an outlet of:
jump-ING Markus Hitter Ingenieurbüro In der Breite 27 78354 Sipplingen Germany Verantwortlich gem. §6 MDStV: Markus Hitter Umsatzsteuer-ID: DE 171 017 618
Urheberrecht
© Alle Rechte vorbehalten.
Insbesondere dürfen Vervielfältigungen nur nach vorheriger schriftlicher Zustimmung des Anbieters erfolgen. Mit der Nutzung der Website www.reprap-diy.com erklären Sie sich mit unseren Nutzungsbedingungen einverstanden. Für die Richtigkeit und Vollständigkeit wird keine Gewähr übernommen. Dasselbe gilt für die Inhalte Dritter, die über diese Seiten zugänglich gemacht werden. In keinem Fall wird für Schäden, die sich aus der Verwendung der abgerufenen Informationen oder dem Versenden von Informationen ergeben könnten, eine Haftung übernommen.
Alle auf dieser Website genannten Produktnamen, Produktbezeichnungen und Logos sind eingetragene Warenzeichen und Eigentum der jeweiligen Rechteinhaber. Haftungsausschluss
Die bereitgestellten Informationen auf der Website www.reprap-diy.com wurden sorgfältig geprüft und werden regelmäßig aktualisiert. Jedoch kann keine Haftung oder Garantie dafür übernommen werden, dass alle Angaben zu jeder Zeit vollständig, richtig und in letzter Aktualität dargestellt sind. Dies gilt insbesondere für alle Links zu anderen Websites, auf die direkt oder indirekt verwiesen wird. Hinsichtlich der Links erklärt Markus Hitter ausdrücklich, dass sie keinerlei Einfluss auf die Gestaltung und die Inhalte der verlinkten Seiten hat und sich diese Inhalte nicht zu eigen macht.